Differences

This shows you the differences between two versions of the page.

--- heater_fabrication [2020/02/25 12:20] – gerry
+++ heater_fabrication [2020/02/25 12:58] (current) – gerry
@@ Line 8: / Line 8: @@
 {{ :heater:heater_parts_before_assembly.jpg |}}
-==== Resistor Location ====
+===== Resistor Location =====
 The leads of the heater resistor should not protrude far beyond the edge
@@ Line 45: / Line 45: @@
 Change the position of the spreader in the vise, and use a file to remove the burr.
-Make sure the surface of the spreader is above the vise.  You don't want to dull the file or scratch the vise by filing the vise instead of the burr.
+Make sure the surface of the spreader protrudes above the vise jaws.  You don't want to dull the file or scratch the vise by filing the vise instead of the burr.
 {{ :heater:heater_drill_burr_file.jpg |}}
@@ Line 54: / Line 54: @@
-==== Attach the resistor to the heat spreader ====
+===== Attach the resistor to the heat spreader =====
 Secure the resistor to the heat spreader with the small screw.  The screw should be snug.  Be careful not to over-tighten the screw as you may strip the soft Aluminum.
 {{ :heater: heater_screw_attach_resistor_to_spreader.jpg |}}
 The screw will protrude from the back side of the spreader.  Flip the resistor/spreader assembly in the vise and use a file to remove the point of the screw.  Again, the goal is to remove any sharp features that may damage the heat shrink applied at the end of the assembly process.
@@ Line 66: / Line 65: @@
-Solder the extension wire to the resistor
+===== Solder the extension wire to the resistor =====
+Move the heater assembly to a solder station and solder the lead wires to the resistor.  Be careful not to overheat the resistor.  In the photo, a heat sink is attached to the resistor leads near the base of the resistor.
+{{ :heater: heater_wiring_solder_resistor.jpg |}}
+Add heat shrink to the exposed resistor leads.
+{{ :heater: heater_wiring_solder_resistor_heatshrink.jpg |}}
-Add heat shrink to the resistor leads
+Before proceeding with the assembly, use a multimeter to verify continuity of the heater assembly.  You want to make sure that the leads have been attached securely and that the resistor is still functioning.
+{{ :heater: heater_multimeter_verify_resistance.jpg |}}
-Verify the heater resistance before sealing the heater
+===== Seal the heater assembly =====
+**STOP HERE:**  Ask the instructor about adding the sealant to the
-Locate the heat spreader in the middle of the large shrink tubing
-STOP HERE:  Ask the instructor about adding the sealant to the
 wires before the heating the heat shrink.
+Locate the heat spreader in the middle of the large shrink tubing.  The first image shows that roughly equal amounts of heat shrink tubing extend beyond each end of the heater assembly.
+{{ :heater: heater_heatshrink_beside.jpg |}}
+Consult with the instructor about adding sealant to the end of the heat shrink that has the wire leads protruding.
+{{ :heater: heater_heatshrink_inside.jpg |}}
-Use a heat gun to secure the end around the wires first.
+After adding sealant to the wire ends, work quickly (no rush, just don't dally) to use a heat gun to shrink the tubing on the end with the protruding wires.  Apply the heat first to the center (at the heater assembly) and then work toward the open end. Some sealant may ooze out of the open end.
-Do not heat the heat shrink tubing until the instructor
-adds sealant to the wires.
+The important feature is that there are no openings for water to enter inside the heat shrink along the wires.
+{{ :heater: heater_heatshrink_closed_end.jpg |}}
+When the wire-end of the heat shrink tubing is finished, apply heat to the open end.  While the open end is still warm, place the tubing in a vise and crush the tubing gently.  You do not need to apply too much force with the vise.
+{{ :heater: heater_heatshrink_closed_end_crushed.jpg |}}
-Heat the free end and crush it in a vise to seal it
+Use a multimeter again to test the continuity of the heater assembly.